MOT for F746EMA is a FORD TRANSIT 100 Motor Caravan with petrol fuel in white with a 7 Speed Manual gearbox, registered on the 1st August 1988, vehicle is 37 years 3 months old and has a expired MOT and Untaxed as of the 14 February 2025.
F746 EMA
| Make | FORD |
| Model | TRANSIT |
| Version | 100 Motor Caravan |
| Fuel | Petrol |
| Colour | White |
| Gearbox | 7 Speed Manual |
| Registered | 1st August 1988 |
| Age | 37 years 3 months old |
| MOT Status | Expired |
| Expiry Date | 14th July 2022 |
| Road Tax | Untaxed |
| Due Date | 1st December 2021 |
| V5 Issued | 11th July 2021 |
FAILED
| MOT test number | 447926960036 |
| MOT test Date | 26th August 2022 |
| Mileage | 74713 |
| Name | Type |
|---|---|
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting out rigger (6.2.2 (d) (i)) | FAIL |
| Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement Front bush (5.3.4 (a) (i)) | ADVISORY |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced Inner wheel arch (6.1.1 (d) (i)) | FAIL |
| Spare tyre defective spare tyre flat () | ADVISORY |
| Offside Front Headlamp insecure (4.1.1 (c)) | FAIL |
| Exhaust mounting defective Rear silencer (6.1.2 (a)) | ADVISORY |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | FAIL |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | FAIL |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | FAIL |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | FAIL |
| Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i)) | FAIL |
| Fuel cap/sealing device missing wrong cap fitted (6.1.3 (b) (i)) | FAIL |
| Offside Front Suspension arm pin or bush worn but not resulting in excessive movement Front bush (5.3.4 (a) (i)) | ADVISORY |
| Exhaust silencer slightly loose front silencer (8.1.1 (b) (i)) | ADVISORY |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | FAIL |
| Offside Front Headlamp aim too high (4.1.2 (a)) | FAIL |
| Exhaust has a minor leak of exhaust gases front silencer (6.1.2 (a)) | ADVISORY |
| Offside Brake pipe clips or supports missing, pipe adequately supported front to rear (1.1.11 (d) (i)) | ADVISORY |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | FAIL |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | FAIL |
PASSED
| Expiry Date | 14th July 2022 |
| MOT test number | 765620884228 |
| MOT test Date | 15th July 2021 |
| Mileage | 73957 |
| Name | Type |
|---|---|
| Nearside Rear Wheel bearing slightly noisy (5.1.3 (b) (i)) | ADVISORY |
| welding repairs to prescribed areas of vehicle is covered in sealer not allowing a full inspection | ADVISORY |
FAILED
| MOT test number | 244902974007 |
| MOT test Date | 12th May 2021 |
| Mileage | 73594 |
| Name | Type |
|---|---|
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | FAIL |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | FAIL |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired Corner (5.3.6 (a) (i)) | FAIL |
| Nearside Lower Suspension spring mounting prescribed area is inadequately repaired Sliding door channel. (5.3.6 (a) (i)) | FAIL |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | FAIL |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired Rear pannel (5.3.6 (a) (i)) | FAIL |
| Welding repairs to prescribed areas/vehicle structure covered in underseal/fibre glass etc. | ADVISORY |
| Nearside Front Subframe mounting prescribed area is inadequately repaired Chassis (5.3.6 (a) (i)) | FAIL |
| Offside Headlamp aim too high (4.1.2 (a)) | FAIL |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | FAIL |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | FAIL |
| Drivers seats fixing bolt load spacer incorrect size. | ADVISORY |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Corner (5.3.6 (a) (i)) | FAIL |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired Wheel arch has filler/fibre reinforcement used and the panel do not feel solid when finger and thumb pressure applied. (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Wheel bearing slightly noisy (5.1.3 (b) (i)) | ADVISORY |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired Inside load door/rear valence. (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Upper Suspension spring mounting prescribed area excessively damaged significantly reducing structural strength Box section. (5.3.6 (a) (i)) | FAIL |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired Rear panel. (5.3.6 (a) (i)) | FAIL |
FAILED
| MOT test number | 458485484901 |
| MOT test Date | 7th April 2021 |
| Mileage | 73576 |
| Name | Type |
|---|---|
| Nearside Front Upper Subframe mounting prescribed area is inadequately repaired Cross member (5.3.6 (a) (i)) | FAIL |
| Welding repairs covered in underseal etc. | ADVISORY |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | FAIL |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | FAIL |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | FAIL |
| Nearside Front Lower Subframe mounting prescribed area is inadequately repaired Cross member (5.3.6 (a) (i)) | FAIL |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired Valence (5.3.6 (a) (i)) | FAIL |
| Offside Rear Inner Suspension spring mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | FAIL |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner wing area (5.3.6 (a) (i)) | FAIL |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired Wheel arch has filler/fibre reinforcement used and the panel do not feel solid when finger and thumb pressure applied. (5.3.6 (a) (i)) | FAIL |
| Offside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Floor sections (5.3.6 (a) (i)) | FAIL |
| Nearside Front Inner Subframe mounting prescribed area is inadequately repaired Wheel arch area (5.3.6 (a) (i)) | FAIL |
| Nearside Headlamp aim too low (4.1.2 (a)) | FAIL |
| Offside Front Subframe mounting prescribed area is inadequately repaired Wheel arch area (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Wheel bearing slightly noisy (5.1.3 (b) (i)) | ADVISORY |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Sill/step (7.1.1 (a) (i)) | FAIL |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Box section shackle mounting. (5.3.6 (a) (i)) | FAIL |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength Floor sections (5.3.6 (a) (i)) | FAIL |
PASSED
| Expiry Date | 29th January 2021 |
| MOT test number | 273557203064 |
| MOT test Date | 30th January 2020 |
| Mileage | 72745 |
FAILED
| MOT test number | 221975387378 |
| MOT test Date | 25th January 2020 |
| Mileage | 72745 |
| Name | Type |
|---|---|
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | FAIL |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | FAIL |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | FAIL |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | FAIL |
PASSED
| Expiry Date | 6th January 2020 |
| MOT test number | 813065139473 |
| MOT test Date | 7th January 2019 |
| Mileage | 71869 |
FAILED
| MOT test number | 703650208830 |
| MOT test Date | 7th January 2019 |
| Mileage | 71867 |
| Name | Type |
|---|---|
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | FAIL |
| Rear Brakes imbalanced across an axle (1.2.1 (b) (i)) | FAIL |
| Central Brake pipe inadequately clipped or supported (1.1.11 (d) (i)) | MINOR |
| Nearside Front Service brake binding but not excessively (1.2.1 (f)) | ADVISORY |
| Rear Exhaust fumes entering cabin box missing (6.1.2 (b) (i)) | FAIL |
| Emissions not tested (8.2.1.2 (d)) | FAIL |
| Rear Brakes imbalanced across an axle by more than 50% (1.2.1 (b) (ii)) | FAIL |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | FAIL |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | FAIL |
| Offside Front Service brake binding but not excessively (1.2.1 (f)) | ADVISORY |
| Rear Exhaust emissions likely to be affected by an exhaust leak box (8.2.1.1 (b)) | FAIL |
FAILED
| MOT test number | 619052183009 |
| MOT test Date | 21st April 2018 |
| Mileage | 71860 |
| Name | Type |
|---|---|
| Exhaust emissions hydrocarbon content excessive (7.3.B.1b) | FAIL |
| Nearside Stop lamp not working (1.2.1b) | FAIL |
| Nearside Front Tyre has ply or cords exposed (4.1.D.1b) | FAIL |
| Nearside Rear Tyre has ply or cords exposed (4.1.D.1b) | FAIL |
| Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | FAIL |
| Nearside Headlamp aim too low (1.8) | FAIL |
| Offside Front Tyre has ply or cords exposed (4.1.D.1b) | FAIL |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner wheel arch (2.4.A.3) | FAIL |
PASSED
| Expiry Date | 24th March 2018 |
| MOT test number | 233468357340 |
| MOT test Date | 25th March 2017 |
| Mileage | 71132 |
PASSED
| Expiry Date | 27th September 2016 |
| MOT test number | 427996548174 |
| MOT test Date | 28th September 2015 |
| Mileage | 65299 |
FAILED
| MOT test number | 106652518455 |
| MOT test Date | 28th September 2015 |
| Mileage | 65299 |
| Name | Type |
|---|---|
| Fuel pipe leaking (7.2.3) | PRS |
PASSED
| Expiry Date | 1st August 2009 |
| MOT test number | 353863518222 |
| MOT test Date | 31st July 2008 |
| Mileage | 67745 |
| Name | Type |
|---|---|
| horn is slightly defective | USER ENTERED |
| front cross member is corroded and holed | USER ENTERED |
| windscreen is starting to delaminate and is cracked in the os lower corner | USER ENTERED |
| both rear wheel bearings are noisey when rotated | USER ENTERED |
FAILED
| MOT test number | 303823718436 |
| MOT test Date | 31st July 2008 |
| Mileage | 67737 |
| Name | Type |
|---|---|
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.A.1) | FAIL |
| windscreen is starting to delaminate and is cracked in the os lower corner | USER ENTERED |
| both rear wheel bearings are noisey when rotated | USER ENTERED |
| Offside Steering rack gaiter split (2.2.D.2d) | FAIL |
| Offside Front Brake hose ferrule excessively corroded (3.6.B.4e) | FAIL |
| horn is slightly defective | USER ENTERED |
| front cross member is corroded and holed | USER ENTERED |
| Nearside Front Brake hose ferrule excessively corroded (3.6.B.4e) | FAIL |
PASSED
| Expiry Date | 1st August 2008 |
| MOT test number | 161204417235 |
| MOT test Date | 2nd August 2007 |
| Mileage | 65170 |
FAILED
| MOT test number | 371514017241 |
| MOT test Date | 2nd August 2007 |
| Mileage | 65168 |
| Name | Type |
|---|---|
| Offside Front Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.D.1a) | FAIL |
| Rear Exhaust has a major leak of exhaust gases (7.1.2) | FAIL |
| Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i) | ADVISORY |
| horn is slightly defective | USER ENTERED |
| Windscreen wiper does not clear the windscreen effectively (8.2.2) | FAIL |
| Exhaust has a major leak of exhaust gases (7.1.2) | FAIL |
| Front Brake pad(s) wearing thin (3.5.1g) | ADVISORY |
| windscreen is cracked and starting to delaminate | USER ENTERED |
| Front brake disc slightly pitted (3.5.1h) | ADVISORY |
PASSED
| Expiry Date | 1st August 2007 |
| MOT test number | 350654116278 |
| MOT test Date | 2nd August 2006 |
| Mileage | 62781 |
| Name | Type |
|---|---|
| front brake rerrule`s corroded | USER ENTERED |
| off side front chassis corroded | USER ENTERED |
| ehaust corroded | USER ENTERED |
| screen cracked, not within the swepped aera | USER ENTERED |
| both sill`s holed | USER ENTERED |